HistoricBridges.org Menu: HistoricBridges.org Menu:


HistoricBridges.org: Bridge Browser

Photos: Half Road Bridge

Original / Full Size Photos

Uncredited photos on this page taken by: Nathan Holth and Luke Gordon. Unless stated in a caption, all photos are Copyright with All Rights Reserved. Learn about reuse of our photos.

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhotoPhotoPhotoPhotoPhoto

Removing the first part of the deck. The only minor challange in removing the deck was the fact that the wooden planks extended under the railing. Because the railings were not removed during the project, the planks kept getting stuck under the railing.

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhotoPhotoPhotoPhotoPhoto

Removal of deck from the center panel.

Divider

PhotoPhotoPhoto

Deck stringers after a section of the wooden deck was removed. Some of the deck stringers were so deteriorated that they made Swiss cheese look solid and practically fell apart under their own weight.

Divider

PhotoPhotoPhoto

Preparing to remove the first group of deck stringers.

Divider

PhotoPhotoPhotoPhotoPhotoPhoto

Deck stringers being removed.

Divider

PhotoPhoto

Views of bridge during deck stringer removal.

Divider

PhotoPhotoPhotoPhotoPhoto

Preparing to remove deck stringers.

Divider

PhotoPhotoPhotoPhoto

Deck stringers being removed.

Divider

PhotoPhoto

Bridge after removal of deck and deck stringers.

Divider

PhotoPhotoPhotoPhoto

Removing nuts holding lateral bracing in place.

Divider

PhotoPhotoPhotoPhotoPhotoPhoto

A few different options existed for removing floor beams. An attempt was first made to see if the hanger bolts could easily be removed by heating the nuts to expand them. This proved too difficult to be worth the effort.

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhoto

Another method was to see if the bottom chord connection pins could be easily driven out. This required holding the floorbeam in place with the crane. Setup for this is shown in these photos.

Divider

PhotoPhotoPhotoPhoto

Attempting to pry at the pin to get it loose and make it ready to be driven out. This did not work.

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhotoPhoto

In preparation for a second attempt, the tension on the pin was removed with these chains and jacks.

Divider

Photo

Second attempt to drive the pin out. The pin still would not come loose.

Divider

PhotoPhoto

Between the challenges of driving the pin out and the fact that the floor beams had enough section loss that they would be replaced in restoration anyway, the decision was made to simply cut the floor beams out.

Divider

PhotoPhoto

General views of the bridge at this point in the project.

Divider

PhotoPhoto

The trusses were secured and braced by welding angles to the end posts before the removal of the second, final, floorbeam. 

Divider

PhotoPhoto

Preparing floor beam for removal.

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhotoPhotoPhotoPhoto

Cutting out the floor beam. Note that this method left the hangers and lateral bracing connections intact so they can be reused during restoration if possible.

Divider

PhotoPhotoPhoto

The final floor beam is removed.

Divider

PhotoPhotoPhotoPhoto

General views of bridge with all floor beams removed. The bridge is now just two independent truss webs sitting on the abutments. Each truss was ready to be simply picked off the abutments and placed on the ground.

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhotoPhotoPhoto

Removing the first truss. 

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhoto

General views of bridge site with first truss removed.

Divider

Photo

Abutment detail after truss removal.

Divider

PhotoPhoto

View of where one of the bearing locations was.

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhoto

Preparing second truss for removal.

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhotoPhoto

Removing the second truss.

Divider

PhotoPhotoPhotoPhotoPhoto

The trusses are set on land, ready to be prepared for dismantling and shipping.  

Divider

PhotoPhotoPhotoPhoto

Overview of bridge site after both trusses were removed.

Divider

Divider

Back
Home
Top

Divider

About - Contact

Divider