HistoricBridges.org Menu: HistoricBridges.org Menu:


HistoricBridges.org: Bridge Browser

Photos: McIntyre Bridge

Original / Full Size Photos

Uncredited photos on this page taken by: Nathan Holth. Unless stated in a caption, all photos are Copyright with All Rights Reserved. Learn about reuse of our photos.

Divider

PhotoPhotoPhotoPhoto

Photo Credit: Julie Bowers

Photos of Nels Raynor, President of Bach Ornamental and Structural Steel of Holt, Michigan who undertook the recovery and restoration of the bridge.

Divider

PhotoPhoto

Photo Credit: Julie Bowers

Photos of Shane Milliken, who also works for Bach Ornamental and Structural Steel.

Divider

Photo

Photo Credit: Julie Bowers

View of the piers missing their bridge.

Divider

Photo

Photo Credit: Julie Bowers

The piers appear largely undamaged.

Divider

Photo

Photo Credit: Julie Bowers

A large portion of the bridge lays downstream in the river.

Divider

PhotoPhotoPhotoPhotoPhotoPhoto

Photo Credit: Julie Bowers

Overview of the area where a large portion of the bridge ended up.

Divider

PhotoPhoto

Photo Credit: Julie Bowers

Some of the damage to the members shows the work that awaits during restoration.

Divider

PhotoPhoto

Photo Credit: Julie Bowers

Work begins on removing splice plate rivets on the top chord, to separate the chord into smaller sections to transport.

Divider

PhotoPhotoPhoto

Photo Credit: Julie Bowers

Preparing to lift a top chord section out.

Divider

PhotoPhotoPhoto

Photo Credit: Julie Bowers

Working to separate the top chord at the vertical member connection.

Divider

Photo

Photo Credit: Julie Bowers

Lifting a vertical member/outrigger.

Divider

PhotoPhotoPhotoPhoto

Photo Credit: Julie Bowers

Lifting top chord sections.

Divider

PhotoPhotoPhotoPhotoPhoto

Photo Credit: Julie Bowers

Separating the parts of bottom chord connections.

Divider

Photo

Photo Credit: Julie Bowers

Navigating the tangled mess.

Divider

PhotoPhotoPhotoPhotoPhotoPhoto

Photo Credit: Julie Bowers

Lifting bottom chord sections out.

Divider

PhotoPhotoPhotoPhoto

Photo Credit: Julie Bowers

Hooking onto and lifting a section of the deck.

Divider

Photo

Photo Credit: Julie Bowers

Fishing for bridge parts.

Divider

PhotoPhotoPhotoPhoto

Photo Credit: Julie Bowers

Fishing a top chord section out.

Divider

Photo

Photo Credit: Julie Bowers

Lifting some of the deck wood out.

Divider

PhotoPhotoPhotoPhotoPhotoPhotoPhoto

Photo Credit: Julie Bowers

Fishing various parts of the bridge out.

Divider

Photo

Photo Credit: Julie Bowers

A vertical member/outrigger is lifted out.

Divider

PhotoPhotoPhoto

Photo Credit: Julie Bowers

Bottom chord section and badly damaged vertical member/outrigger is lifted out.

Divider

PhotoPhotoPhotoPhotoPhotoPhoto

Photo Credit: Julie Bowers

Searching for and lifting out bottom chord sections.

Divider

PhotoPhoto

Photo Credit: Julie Bowers

Getting pin nuts that may have not been turned for over a century is not as difficult as it might seem. Simply heat the nut, which causes the metal of the nut to expand. Here, the removal of a nut for a bottom chord pin connection is to be removed to separate the bottom chord into smaller sections for transport.

Divider

Photo

Photo Credit: Julie Bowers

Once heated, the nut will turn.

Divider

PhotoPhoto

Photo Credit: Julie Bowers

Here the nut has been removed, the pin remains in place.

Divider

PhotoPhoto

Photo Credit: Julie Bowers

If the pin is stuck or frozen in place, a pneumatic hammer can be used to safely push it out, which was the case here.

Divider

PhotoPhoto

Photo Credit: Julie Bowers

Here, the bottom chord connection is shown with the pin removed.

Divider

PhotoPhoto

Photo Credit: Julie Bowers

Some of the top chord box beams had mud inside, so they were dipped back in the water to wash them out.

Divider

Photo

Photo Credit: Julie Bowers

A top chord section is loaded for transport.

Divider

Photo

Photo Credit: Julie Bowers

A damselfly watches the events at the site.

Divider

Divider

Back
Home
Top

Divider

About - Contact

Divider